CANON LASER CLASS 730I FAX DRIVER DETAILS:
|File Size:||36.9 MB|
|Supported systems:||Windows 10, Windows 8.1, Windows 8, Windows 7, Windows 2008, Windows Vista|
|Price:||Free* (*Free Registration Required)|
CANON LASER CLASS 730I FAX DRIVER
Do not store cartridges in locations subject to extreme fluctuations in temperature and humidity. To prevent caking of the toner, never stand the cartridge on its end, and do not store it upside down. If the toner becomes caked as a result of being stored in an odd position for too long, it may be impossible to dissolve it completely even by shaking the cartridge. Do not store the cartridge in salty or corrosive air. Canon laser class 730i fax attempt to disassemble a toner cartridge or attempt to refill it. Make sure that you use a stored toner cartridge before the expiration date printed on the toner cartridge box.
Loading Paper into Paper Cassettes If your machine comes with more than one paper cassettes, you can use this procedure for each one. The paper cassettes can be adjusted to hold letter, legal, executive, A4, A5, and B5 paper size, and can hold up to approximately sheets of paper. Do not load the following paper into the paper cassettes: - Moist paper - Paper that is wavy, curled, or damaged - Folded, clipped, or stapled paper - Paper containing materials that melt, vaporize, offest, discolor, or emit dangerous fumes at a temperature of F C or higher To avoid paper curling, do not open the paper packages until you are ready canon laser class 730i fax load the paper into the machine.
Store unused paper from opened packages in a cool, dry location. Let the paper run out before you refill the paper cassettes.
Canon Laser Class 730i Fax Machine Reconditioned
Avoid mixing new paper with paper remaining in the paper cassettes. Do not load different paper sizes in the paper cassettes at the same time. If a printed page comes out of the machine all curled up, you can correct the problem by turning over the paper stack in the paper cassettes so that the bottom sheet in the stack is now at the top. If the leading edge of the paper is curled, straighten it out as much as possible before loading it into the paper cassettes. Do not set the paper size guides so tight that the paper stack bends. Adjust the paper size guides so that there is no room between the guides and the paper stack.
The MP tray can also hold nonstandard paper sizes, and envelopes. For details on the types of paper you can set on the MP tray. Do not use the following canon laser class 730i fax in the MP tray: - Moist paper - Paper that is wavy, curled, or damaged - Folded, clipped, or stapled paper - Paper with cut-outs or perforations - Paper containing materials that melt, vaporize, offset, discolor, or emit dangerous fumes at a temperature of F C or higher Avoid pressing or applying excessive force on the MP tray, as this may cause canon laser class 730i fax.
Canon LASER CLASS 730i Manuals
The paper stack must not exceed the paper limit mark. Do not load different sizes of paper in the MP tray at the same time.
Do not add paper to the MP tray if paper is already loaded; incorrect paper feeding, or a paper jam may occur. Only add paper when the MP tray is empty. Do not set the paper guides so tight that the paper stack canon laser class 730i fax. The following six printed circuit boards are located in this machine: 1.
Canon LaserClass i Network MFP Scan Copy Fax Printer
NCU board that interfaces with the telephone line Hybrid circuit Line voltage conversion circuit 3. Fixing heater control High voltage control Drive control Sensors detection Laser control Scanner motor control 5. EPU board on which the fixing heater control circuit and the high-voltage power supply circuit are mounted. A Power supply unit is also located in this machine Switching regulator 8. Sensor board used to monitor canon laser class 730i fax sensors in the reader unit. Sensors 9.
G3 FAX board Dual-line option used to control the circuit communications block. Dual-line communications unit control NCU board that interfaces with the telephone line Dual-line option Hybrid circuit Line voltage conversion circuit Document width sensor Document feed sensor Document sensor.
Document width sensor DWS : It detects the width of the document. Document feed sensor DFS : It detects the feed condition of the document. Document edge sensor DES : It detects the lead canon laser class 730i fax rear edges of a document. Page top sensor: It detects the lead and the rear edge of the recording paper.
Face-up sensor: It detects the face-up tray conditions. Paper eject sensor: It detects the recording paper eject conditions. Tray full sensor: It checks the full loading of recording paper. Paper Guide It is used to hold down the original in horizontal direction to prevent it from moving askew. Pickup Roller The cam is rotated by the DC motor, and the document stopper moves into a free condition. At this time, the pickup roller moves down and the canon laser class 730i fax is fed.
- Canon LASER CLASS i - multifunction printer ( B/W ) Series Specs - CNET
- Canon LaserClass LCi Fax Machine
- Canon Laser Class i Fax Machine RECONDITIONED
- Canon LaserClass 730i Network MFP Scan Copy Fax Printer
- LASER CLASS 730i
Separation Roller upper This roller uses differences in the coefficients of function of the document and separation roller to separate each of the sheets in a multiple-page document. Separation Roller canon laser class 730i fax This roller uses differences in the coefficients of function of the document canon laser class 730i fax separation roller to separate each of the sheets in a multiple-page document.The LASER CLASS i Internet Facsimile System is the flagship model of the LASER CLASS Series. It comes standard with Internet Fax, PC Fax, local and. Canon LASER CLASS i - multifunction printer - B/W overview and full product specs on impressions. Fax Type. Plain paper.